Every safety recall published by the Australian government, searchable and filterable.
Due to a Transmission Control Module (TCM) programming issue, the transmission may rev faster than intended causing a loss of motive power and transmission fluid to leak. A transmi…
Due to a Transmission Control Module (TCM) programming issue, the transmission may rev faster than intended causing a loss of motive power and transmission fluid to leak. A transmi…
Due to a manufacturing defect, the trailer control valve was incorrectly mounted and do not comply with the requirements of the Australian Design Rule (ADR) 35/07 - Commercial Vehi…
Due to a manufacturing defect, the Airbag Control Unit (ACU) software may have been calibrated with higher than intended sensitivity. As a result, the driver, passenger, curtain ai…
Under certain driving conditions the upper triple clamp that secures the handlebar may fracture. This could lead to a loss of vehicle control whilst riding.
During the manufacturing process, the Restraint Control Module (RCM) was loaded with an incorrect configuration. As a result, if an incorrect replacement part is installed in the s…
Due to a manufacturing defect, the starter motor solenoid switch can experience increased wear that could cause an internal short circuit. If this occurs, the driver may be unable…
Due to a software issue, the brake fluid warning light may not illuminate as intended to warn the driver if the brake fluid level is low. As a result, insufficient brake fluid coul…
Due to a software issue, under certain circumstances if the battery level drops below a critical threshold, the transmission may shift into Park when the vehicle is travelling at s…
Due to a potential fault in the Light Emitting Diode (LED) Driver Control Module (LDCM) this module may fail. As a result, high beam, low beam, position lamps and daytime running l…
Due to a manufacturing defect, the rear brake hose could be susceptible to heat damage and may result in a sudden loss of rear braking performance. The front brake will continue to…
On certain vehicles, the cover on the rear swing door in the loading bay are missing, resulting in door strikers being exposed to occupants.
Due to a manufacturing defect, the Electronic Control Unit (ECU) wiring harness may chafe against the engine mounting bracket and become damaged. As a result, this could lead to a…
Due to a manufacturing issue, the wiring harness under the front seats may not have been positioned according to specifications. As a result, it may become damaged over time and af…
Due to a manufacturing defect, moisture may enter the rear light bar assembly unit. This can cause the reverse lamps to become inoperative or to flicker intermittently.
Due to a manufacturing issue, the cell modules installed in the high voltage battery may be defective and could overheat. If this occurs, it could lead to a vehicle fire. The range…
Due to a manufacturing defect, the transmission wiring harness may chafe against the front drive shaft and become damaged. This could lead to a sudden loss of motive power whilst d…
Due to a manufacturing defect, the rear tyre steel belt may become damaged under certain off-road conditions or riding extended periods with low tyre pressure. This can lead to a l…
Due to a software issue, the Instrument Panel Cluster (IPC) may fail to illuminate the visual vehicle speed, lane keep assist and Advanced Emergency Brake System (AEB deactivation…
Due to a manufacturing defect, the left-hand rear drive shaft may have been incorrectly installed. As a result, it could lead to a loss of motive power whilst driving and/or uninte…
Due to a manufacturing issue, the cell modules installed in the high voltage battery may overheat at high charge levels. If this occurs, it could lead to a vehicle fire.Note: Keep…
Due to a manufacturing defect, the Occupant Restraint Controller (ORC) module may disable the Electronic Stability Control (ESC). If this occurs, the ESC may fail without warning r…
Due to a manufacturing issue, the cell modules installed in the high voltage battery may be defective and overheat during charging. If this occurs, it could lead to a vehicle fire.…
Due to a manufacturing defect, the power steering pump O-ring seal may have been damaged allowing fluid to leak. If this occurs, it could lead to increased steering effort resultin…
Due to improper assembly, the indicator and rear lamp control switch wiring harness may become damaged due to vibration which could cause an internal short circuit. If this occurs,…