37 safety recalls published for the Land Rover Range Rover (2017–2025).
Due to a manufacturing defect, the rear centre seat belt anchor buckle may not meet specifications. As a result, the seat belt may not properly latch or operate as intended.
Due to a manufacturing defect, the high voltage battery may experience cell degradation. This can result in a loss of motive power and a vehicle fire.
Due to a manufacturing defect, the passenger airbag may tear during deployment. This could cause hot gases to escape from the airbag and result in insufficient protection to the pa…
The clutch plates within the hybrid transmission may not meet manufacturing specifications. As a result, the clutch plates may overheat causing material degradation and potential t…
The clamps retaining the engine’s fuel injectors may not meet manufacturing specifications and could crack. If this occurs, fuel may leak in the presence of an external ignition so…
Due to a manufacturing defect, the threaded nut securing the engine oil cooler hose may not have been tightened sufficiently. As a result, the cooler hose could become loose and de…
Due to a manufacturing defect, the rear tail lamps wiring harness may become lodged between the vehicle body and a foam block. If this occurs, the rear tail lamp may not illuminate…
Due to an installation issue, certain 7-seat vehicles may have a latch installed with a defective weld in the second-row seat frame which will stop the seat from securing into the…
Due to a manufacturing defect, under certain conditions the engine may rapidly overheat and subsequently rupture the engine mounted plastic elbow in the cooling system. This could…
Due to a manufacturing issue, the camshaft carrier oil gallery may not have been drilled to specification. This could cause an external oil leak or oil to be discharged into the en…
Due to a manufacturing defect, the exhaust bracket fixing nuts may not have been tightened to specifications and could become loose or detach over time. This may cause hot exhaust…
The chemical mix ratio in some initiators used in the manufacture of seatbelt pre-tensioners may not meet specification, which may cause the initiator to malfunction. In the event…
The routing of the engine harness may not provide sufficient clearance and as a result, allow contact with the Exhaust Gas Recirculation (EGR) casting bracket.Vehicles included in…
The mixture of chemicals used in front passenger airbags on certain vehicles may not meet specification, which may result in the initiator not properly functioning and the front pa…
Under bonnet fuel hoses routed on top of the engine may chafe against a plastic moulded noise suppressing material retaining posts of the underside of the engine top cover. The Noi…
Some customers have reported the inability to secure the door in the closed position, either on the primary or secondary latch. In addition, there have been reports that one of the…
The wheel nuts may be made from material where the ultimate tensile strength (UTS) is lower than required specification. In this condition some wheel nuts may crack and detach from…
The Brake Vacuum Hose may be incorrectly installed. Incorrect routing of the brake vacuum hose can lead to a chafing condition, eventual rupture of the hose and complete loss of va…
The front brake flexible hoses may rupture.
The front direction indicator lamp diagnostics do not provide the legally required double click/double flash warning required.
A concern has been identified where the battery positive cable on 2014 model year Range Rover Sport SDV6 vehicles fitted with Dynamic Response System (DRS) suspension system may cl…
The driver may experience abnormal noise from the rear of the vehicle when driving or when the brakes are applied. In rare cases, this may indicate that one or both of the brake c…
The driver could experience abnormal noise from the front of the vehicle during low speed manoeuvring. In rare cases, this may indicate a fatigue fracture in one or both of the st…
The affected vehicles windshield may not be chemically bonded to the Polyurethane (PU) adhesive. Where the windshield is not chemically bonded, water ingress may occur and there ma…
The television may continue to operate if the telephone is used while the vehicle is stationary. The television operation could distract the driver and is a breach of the ADRs.
A cooling system gasket located below the throttle body housing may leak and expel fluid onto hot engine components.
Premature failure of cooling system hoses. Hose failure may cause a roadside breakdown. Important all traces of coolant are removed as if allowed to remain on hot engine componen…
Failure Of The Power Steering Pump Pulley May Occur At Low Kilometres As A Result Of Fatigue Cracks. In The Event Of Failure The Serpentine Drive Belt Will Be Subject To Damage R…
Possibility Of The End Of The Automatic Gearbox Breather Pipe 'icing Up' In Extreme Sub Zero Ambient Temperatures.
Possible Premature Failure Of Under Bonnet Hoses With A Resultant Coolant Loss Resulting In An Under Bonnet Fire In The Presence Of An Ignition Source.
Failure In The Rear Radius Arm Chassis Eye End Due To Stress Corrosion Cracking And/or A Cold Weld Condition.
Failure Of The Engine Idler Pulley May Result In Damage To Drive Belt With Resultant Loss Of Power Assisted Steering And Ancillary Component Drive.
Abs High Pressure Hoses May Fracture Resulting In Loss Of Power Brakes.
All Rear Brake Lights May Fail When The Brakes Are Applied On Vehicles Equipped With Centre High Mounted Stop Lamps When Anti-lock Brakes Are Also Fitted.
To Check Tyre Fitment And Replace Tyre If Necessary.
Possible Defect Of The Brake Pedal Box Assembly And Rear Brake Line: Vehicles To Be Checked And/or Corrected.
The Sensitivity Device In Inertia Reel Seat Belts, May Not Be Effective In Locking The Reel.