Every safety recall published by the Australian government, searchable and filterable.
Due To The Materials Used In Manufacturing The Front Chain Drive Sprocket Locking Plate, It Can Possibly Wear Causing The Locking Function Of The Plate To Fail And No Longer Lock T…
Failure May Occur Of The Torque Rod Pin That Assists In The Location Of The Rear Drive Axles,
The Front Suspension Lower Ball Joints Have Polyacetal Plastic Seats And May Have Ball Pins With A Rough Surface Resulting In Rapid Wear With Possibility Of Joint Separating And Re…
A Wiring Harness Close To The Top Of The Accelerator Pedal May Interfere With The Travel Of The Pedal Which Could Possibly Hold The Accelerator Open.
A Wiring Harness Close To The Top Of The Accelerator Pedal May Interfere With The Travel Of The Pedal Which Could Possibly Hold The Accelerator Open.
The Wheel Bolts And The Alloy Wheel May Not Be Compatible In The Wheel Bolt Seat Area, Therefore The Wheel Bolt May Not Seat Correctly And As A Consequence Lead To The Wheel Coming…
Lower Crankcase Bolt Replacement Due To Oil Weep From Between The Engine Crankcase Halves Which Could Cause Vehicle Instability.
May Experience A Malfunction Of The Vacuum Pump Check Valve Which Could Cause Insufficient Vacuum To Be Supplied To The Braking System Resulting In Poor Brake Performance With Incr…
Fuel Hose In The Engine Bay To Be Replaced To Prevent Possible Leakage Of Fuel And The Further Possibility Of Leaked Fluid Catching Fire If Exposed To Certain Elements.
The Sensing And Diagnostic Module Which Is Part Of The Supplemental Restraint System May Have Been Manufactured With Potentially Faulty Microprocessors Which May Sense Inaccurate I…
May Be Insufficient Weld Penetration Of The Spot Weld That Attaches The Child Restraint Anchorage Bracket To The Rear Panel.
The Bolts Securing The Upper Suspension Arm To Upper Arm Bushes May Be Affected By Hydrogen Embrittlement Resulting In Suspension Noise And In Extreme Cases, Upper Arms May Separat…
The Vehicle-down Sensor May Be Dislodged From Its Normal Mounting Position During Battery Maintenance. If The Sensor Is Not Correctly Installed The Engine May Stop In Certain Situ…
Possible Lack Of Lubrication During Assembly Of The Rear Axle Roller Bearing Which May Cause A Failure Of This Component.
The Fuel Line Between The Fuel Tank And Fuel Filter May Operate Incorrectly And Restrict Fuel Flow To The Engine.
A Fuel Line Inside The Fuel Tank May Operate Incorrectly And Restrict Fuel Flow To The Engine.
Potential Failure Of The Handlebars. The Original Handlebars Will Be Replaced By An Improved Re-design Handlebar.
The Lower Part Of The Front Seat Belts May Contact The Edge Of The Backrest Recliner Mechanism Housing, Behind The Seat Valance. Repeated Contact Of This Nature May Eventually Cau…
Possible Seizure Of The Transmission Components Resulting In Rear Wheel Lock-up With Loss Of Control Of The Motorcycle.
The Priority Valve Adaptor Needs To Be Changed As Under Certain Conditions During Rapid Steering A Temporary Loss Of Brakes And Hydraulic Functions May Occur.
Voltage Peaks Caused By Different Items Of Electrical Equipment Such As Relay For Horn, Can Lead To Accidental Triggering Of The Drivers Airbag Which Can Cause Injury.
Defect In The Front Seat Belts May Cause The Pre-tension Device Not To Deploy In An Accident Or Possibly Result In Risk Of Fire In The Base Of The Pillar Where The Seat Belt Retrac…
The Specified Torque Setting For The Upper And Lower Control Arm To Rear Suspension Arm Bolts May Not Have Been Achieved In Production Resulting In Poor And Unpredictable Vehicle…
May Be Equipped With Cruise Control Cables That Are Too Short Causing One End Of The Cable To Unclip And Possibly Interfere With The Throttle Cable.
Possibility Of The End Of The Automatic Gearbox Breather Pipe 'icing Up' In Extreme Sub Zero Ambient Temperatures.