Every safety recall published by the Australian government, searchable and filterable.
The Hydraulic Electronic Control Unit (HECU), responsible for the Anti-lock Braking System, Electronic Stability Control System and Traction Control System, can remain live even wh…
The Hydraulic Electronic Control Unit (HECU), responsible for the Anti-lock Braking System, Electronic Stability Control System and Traction Control System, can remain live even wh…
The Hydraulic Electronic Control Unit (HECU), responsible for the Anti-lock Braking System, Electronic Stability Control System and Traction Control System, can remain live even wh…
The Hydraulic Electronic Control Unit (HECU), responsible for the Anti-lock Braking System, Electronic Stability Control System and Traction Control System, can remain live even wh…
The Hydraulic Electronic Control Unit (HECU), responsible for the Anti-lock Braking System, Electronic Stability Control System and Traction Control System, can remain live even wh…
The Hydraulic Electronic Control Unit (HECU), responsible for the Anti-lock Braking System, Electronic Stability Control System and Traction Control System, can remain live even wh…
The Hydraulic Electronic Control Unit (HECU), responsible for the Anti-lock Braking System, Electronic Stability Control System and Traction Control System, can remain live even wh…
Due to a manufacturing defect, the main wiring harness may come in contact with the steering column shaft and become damaged. This may result in the loss of power assisted steering…
The vehicle specification sheet obtained from the LDV website may have provided incorrect information in relation to gross vehicle mass, axle capacities, payload and towing capacit…
Due to a manufacturing defect, a component of the brake booster system may have been incorrectly welded and could break. If this occurs, a higher pedal force will be required and t…
Due to a manufacturing defect, a component of the brake booster system may have been incorrectly welded and could break. If this occurs, a higher pedal force will be required and t…
Due to a manufacturing defect, the front passenger seat mounting bolts may not have been tightened according to specifications and could become loose or detach. As a result, the s…
Due to a manufacturing defect, oil cooler lines could burst resulting in a sudden loss of oil pressure. This could lead to the engine stalling or an oil leak. An oil leak in the pr…
Due to a manufacturing defect, the Steering Column Control Module (SCCM) may have not been welded to the required specifications. As a result, the SCCM could fail to send an airbag…
Due to a manufacturing defect, the front passenger seat mounting bolts may not have been tightened according to specifications and could become loose or detach. As a result, the s…
The circuit design inside the relay is configured incorrectly. Therefore, the flashing cycle of the turning signal will not comply with the Australian Design Rules (ADR).
Due to a software issue with the Electronic Brake Control Module (EBCM), the brake fluid warning light may not illuminate as intended and therefore fail to warn the driver when the…
The manual release cable of the bonnet latch may have excessive tension which potentially may cause the latch to open. If this occurs, the bonnet could open unexpectedly whilst the…
The high-voltage battery management software has insufficient protections for short circuit events. As a result, if a short circuit occurs it could lead to a vehicle fire whilst dr…
The rear suspension may not meet manufacturing specifications and could buckle. If this occurs, there is a risk of contact between the rear tyre and the chassis, the main wiring ha…
Due to a manufacturing issue, the airbag wiring harness under the rear passenger seat may not have been adequately secured. As a result, it may become damaged over time due to seat…
Due to a manufacturing defect, moisture may enter the front and rear wheel speed sensors. If the sensors are exposed to moisture ingress:• the speedometer may not display as intend…
The jack provided with the vehicle may not include a base plate. The jack does not comply with the mandatory standard for vehicle jacks Consumer Protection Notice No. 1 of 2010 Con…
Due to a manufacturing defect, the Steering Column Control Module (SCCM) may have not been welded to the required specifications. As a result, the SCCM could fail to send an airbag…
Due to a manufacturing defect, the Steering Column Control Module (SCCM) may have not been welded to the required specifications. As a result, the SCCM could fail to send an airbag…